DEWALT Table Saw Memorial Day Sale 2022

Are you looking for DEWALT Table Saw Memorial Day Sale 2022? This article will give you a complete guide for DEWALT Table Saw black friday or Cyber Monday new sales and discounts.

  • Circular Saw
  • 57° Beveling Capacity
  • Durable & Lightweight
Check at Amazon
Editor's Choice
  • Circular Saw with Brake
  • 57° Bevel Capacity
  • Easy To Use
Check at Amazon
  • Sliding Compound Miter Saw
  • Accurate And Durable
Check at Amazon
  • Jig Saw
  • 0°, 15°, 30°, 45°
  • 20V
Check at Amazon
  • Cordless Circular Saw
  • 57° Bevel Capacity
  • 5200 RPM
Check at Amazon
  • Wet Tile Saw
  • Stainless Steel Rail System
Check at Amazon

DEWALT Table Saw Memorial Day Sale 2022

I’ve been using my DeWALT table saw for a few years now, and it felt like a good time to review it. Let’s start with the things I like about the saw. When I bought the saw, I checked the accuracy of the fence. At that time, it was aligned perfectly. After using it for a while and checking it every few months, it stayed that way.

DEWALT Table Saw Memorial Day Sale


It’s perpendicular to the blade, square with the surface, and friendly and flat. It’s also nice and sturdy when locked down—nothing to complain about the central part of the fence.

DEWALT Table Saw Black Friday and Cyber Monday Deals 2022

The fence’s extension also works well to support the workpiece when cutting something more comprehensive than the table. However, unlocking it is a pain. There is room for improvement there.

DEWALT Table Saw Black Friday


The tape measure on the rails of the saw needed a little bit of fine-tuning on purchase. I’m talking 2/10ths of an mm. After correcting the error, it has been cutting accurately ever since. I do regularly double-check to be safe, but it hasn’t let me down yet. I think this is largely because of the rail system that DeWALT uses.

Unlock/Lock Option

Another aspect of the saw that’s good. The fence position is easily changed with just two tabs that you unlock and lock. The screws inside the rails that the fence hooks on are super sturdy and stay parallel after switching position.

What I don’t use is the knob that is added for moving the fence. I slide it over to where I need it to be and tap it back and forth to micro-adjust. The knob doesn’t add much convenience, in my opinion.

Motor Power

Since buying this saw, I haven’t found the limit to what it can cut. What I mean by that is that the motor is an absolute beast. Of course, the blade is limited by its size, and so is the maximum depth of cut.

DEWALT Table Saw cyber monday

But there is no lack of power. Hardwoods of any kind go through without any issues. I do have to mention I don’t use the stock blade and have separate ripping and cross-cutting blades.

Start/Stop Buttons

The start and stop buttons are decent, not great. I have to press it on in one go firmly, or it causes my circuit to blow out in the shop. Not a significant issue if you use it correctly, but it could be better.

The kill switch also works OK. The paddle could be more extensive, and I feel it has to be pressed in rather far. If it turned off a little bit easier, it would be better. Tilting the saw is about the same as the button.

Once you unlock the mechanism, it kind of swings down the entire saw. Getting it set to 23 degrees, for example, is, therefore, a challenge. Especially since when you try to lock it down, you have a good chance of pushing it away further.


What I don’t like about the saw. I know it’s a job site saw, so there is no quiet belt-driven motor, but still, it could be quieter. I’ve used other saws since purchasing the DeWALT, and my saw is the loudest. I wear hearing protection all the time, so it’s a minor point but still a downside to this machine.


Another thing that I don’t like is the dust extraction. It just doesn’t work. I have a pretty powerful shop vacuum attached to the saw, but after just cutting a few boards, I have to clean up everywhere. This is probably true for all saws of this size and price range, but it’s still a pretty big downside.

DEWALT Table Saw deals

Some other points that perhaps are only true for my saw. The T-tracks are not consistent in width across the length of the track. This makes it challenging to make slides for the track or use off-the-shelf tracks. I solved this by finding the most narrow spots and removing material from the saw.

Final Words

The blade is rather large so that pieces can get stuck between the blade and the insert plate. I’ve had this happen several times; one time, it even bends my blade into the plate, cutting a chunk out of it. It’s also not completely flat, and the adjustment can’t fix it.

Last but not least, the length of the power cord. It’s pretty short. I use my saw in a homemade mobile workstation, and my range with it is limited because of this short cord. A little bit of extra length wouldn’t hurt.

About the author

M. Ali

Leave a Comment